The short answer
Chimney liner installation adds or replaces a protective flue inside your masonry chimney so exhaust and heat leave the house safely. In South Williamsburg's older rowhouses and pre-war buildings, a new liner is often needed after an oil-to-gas boiler conversion or when a camera inspection finds cracked or poorly sized clay tiles.
A chimney liner is the protective channel inside your flue. It carries smoke and exhaust gases out of the house and keeps heat and corrosive byproducts away from the surrounding brick and framing. Many South Williamsburg homes are older rowhouses and pre-war apartment buildings with masonry chimneys. Their original clay tile liners are often cracked, missing in sections, or sized for a heating system that was replaced long ago. TrueHearth Chimney Service installs new liners for homes and buildings in ZIP code 11249, working from our office in Prospect Heights, about 2 miles south.
Why Liners Fail in Older Brooklyn Chimneys
Masonry chimneys in this part of Brooklyn have usually been through many decades of heating seasons, building settlement, and freeze-thaw cycles. Clay tiles crack, the mortar joints between them erode, and some older chimneys were built with no liner at all. A damaged flue can let heat reach nearby wood framing. It can also let exhaust, including carbon monoxide, seep through gaps in the masonry into living spaces or neighboring units.
Liner damage is not always visible from the fireplace or boiler room. Signs we look for include:
- Pieces of tile or crumbling mortar at the base of the flue or in the cleanout
- Water stains, white residue, or damp spots on walls next to the chimney
- Flaking or spalling brick on the chimney exterior
- Smoke rolling into the room, weak draft, or exhaust odors near the appliance
- A recent change of boiler, water heater, or fuel type

Oil-to-Gas Conversions and Your Chimney
If your building is converting its boiler from oil to gas, the chimney has to be evaluated as part of the work. That is a New York City requirement. A new liner is often needed because gas exhaust produces acidic condensate, and that moisture can corrode an unlined or clay-lined masonry flue over time.
Liner size matters too. A modern high-efficiency boiler or water heater produces cooler, lower-volume exhaust than an old oil burner. In an oversized flue, that exhaust can cool too quickly, condense on the walls, and draft poorly. We match the liner's diameter and material to the appliance manufacturer's venting requirements.
Liner Options for South Williamsburg Homes
The right liner depends on what the chimney serves and the condition of the flue. Our certified technicians will explain which of these fits your chimney:
- Stainless steel liners: the most common choice for relining, available in flexible or rigid sections for gas, oil, and wood-burning appliances when the correct alloy is used
- Aluminum liners: used for some gas appliances where the manufacturer and code allow it
- Cast-in-place liners: a mortar-type material poured around a form inside the chimney, which can also reinforce deteriorated masonry
- Liner insulation: a wrap or poured material around a metal liner that keeps flue gases warm and helps draft
Time for your annual chimney check?
How Liner Installation Works
Every liner job starts with an inspection. The NFPA 211 standard calls for chimneys to be inspected once a year. It calls for a more detailed Level 2 inspection when the system changes, such as a new appliance or a switch of fuel, and when a home is sold. A Level 2 inspection includes a video camera scan of the flue interior. The camera shows cracks, gaps, and blockages that can't be seen from the roof or the base.
From there, a typical installation follows these steps:
- Clean the flue so the camera and the new liner have a clear path
- Measure the flue and confirm the appliance's venting requirements
- Lower the liner from the roof and connect it to the appliance at the base
- Install a top plate and rain cap to keep out water, debris, and animals
- Walk you through the finished work, including camera footage when helpful
Planning Around Heat Season
New York City's heat season runs from October 1 through May 31. During those months, building owners must keep apartments heated to the city's minimum temperatures. If your boiler vents through a damaged flue, relining during the warmer months lowers the chance of a winter heating outage. If a problem turns up mid-season, we'll talk through how to schedule the work so your heat is off for as little time as possible.
Beyond South Williamsburg, we also install chimney liners in nearby Clinton Hill, Fort Greene, Bedford-Stuyvesant, Downtown Brooklyn, and DUMBO.
More services in South Williamsburg
- Chimney Sweep in South Williamsburg
- Chimney Inspection in South Williamsburg
- Chimney Repair in South Williamsburg
- Air Duct Cleaning in South Williamsburg

